Digi DC-180 Wartungshandbuch

73349 DC-180 OOOOppppeeeerrrraaaattttiiiioooonnnn &&&& SSSSeeeerrrrvvvviiiicccceeee MMMMaaaannnnuuuuaaaallllCCCCoooouuuunnn

103.4. Unlocking Procedure (Continued) for 5LB. To 50LB. ScalesINITIAL SET-UP PROCEDURESBefore setting up the scale, remove the load cell locking scre

11Do not unplug remote scale from the DC-180 while the DC-180 is powered.3.4. Unlocking Procedure (Continued) for 1LB. and 2.5LB. ScalesThe above draw

124.0. DC-180 AC / BATTERY OPERATIONThe DC-180 can be operated with AC power or with the optional internalbattery. The battery will automatically cha

135.0. Operation Guide in Weighing Mode5.1. Tare Reduction :5.1.1. One Touch Tare Operation :1 Display in the weighing mode2 Place 0.5 Lb weight on th

145.3. Unit Weight Operation :5.3.1. Unit Weight Operation by Sampling :1 Display in the weighing mode2 Place 10 pcs of the item to be sampled on the

155.4. Accumulation Operation :This following procedure is used if the unit weight is already known.1 After Unit Weight entry. (See 4.3)2 Press the [+

165.6. Clearing of Accumulated Data :1 From previous operations (See 4.4. & 4.5.)2 Pressing the [∗∗∗∗] key, clears the accumulated total. 5.7

175.9. Recall Item From Memory:Version 1.13 and above ID CODE (30 ITEM MEMORY)OPERATION EXAMPLE : Recall Item From Memory:Task Procedure1. Select Sca

186.0. PROGRAMMING MODE:6.1. Set Point Programming :6.1.1. Set Point Programming by % QuantitySet Point 1 : Quantity (See Note Below) , Set Point 2 :

196.1.3. Set Point Programming by Upper and Lower Limit of QuantitySet Point 1 : Quantity (See Note Below), Set Point 2 : Quantity (See Note Below)Set

206.2. PROGRAMMING ID CODE (30 ITEM MEMORY)Version 1.13 and above PROGRAMMING ID CODE (30 ITEM MEMORY)Task Procedure1. Enter PROGRAM Mode. Press [M

217.0. MAINTENANCE MODE:7.1. Scale Calibration :Prior to the calibration of the scale, please note that the SPEC settingscorresponding to Minimum Disp

227.4. Internal Count And A/D Count Display :If the SPEC 25, bit 2 is set, then the [SPAN] Switch must be "ON" to enter this mode.1Enter [0]

237.5. DC-180 Spec. List Rev. 7Operation Specifications : To enter this mode, enter the numeric keys 1,4,1 while pressing the RezeroKey.Spec No. Bit

24Weight and Measures Specification : To enter this mode, enter the numeric keys 1,4,2while pressing the Rezero Key. The Span Switch must be “ON” to

25Spec No. Bit 3 Bit 2 Bit 1 Bit 030 Load Cell Sensitivities Selection (mV/V) (Scale 1)Spc Min Max Spc Min Max Spc Min Max Spc Min Max0000000100100011

267.7. Shop Notes:

1DC-180 Limited WarrantyRice Lake Weighing Systems (RLWS) warrants that all RLWS equipment and systems properly installed by aDistributor or Original

3DC-180 SERIES OPERATING MANUALINDEXSECTION PAGENUMBER1.0 GENERAL 4-71.1. Description 41.2. Keyboard & Display Layout 51.3. Indicator Lam

41.0. GENERAL1.1. DescriptionThe DC-180 counting scale offers a practical solution to a full range of precisioncounting applications. There are a var

51.3. Keyboard & Display Panel Layout

61.4. Indicator Lamp InformatonLAMP “ON”Zero When the gross weight is zero.Tare When tare weight is set.Gross When [Gross/Net] key is pressed.Insuff

71.5. Key Switch InformationKEY FUNCTIONSOn/Off For turning the machine ON and OFF.0 to 9 Numeric Keys..Decimal Point.Rezero Used to reset the scale t

82.0. SPECIFICATIONSThis section includes a detailed listing of all pertinent specifications and parameters for theDC-180 counting scales. The system

93.0. INSTALLATIONThis section provides the information required for installing this counting systemFor operation. The following steps accomplish ins