Digi MIL-3310FTX Betriebsanweisung

FastPort™ User’s Guide CD-ROM Version For... “Legal”: Click here“Table of Contents”: Click here“Preface”: Click here“Introduction”: Click here“Settin

FastPort User’s Guide 1-1 Chapter 1 Introduction Chapter 1 gives the requirements and features for configuring all FastPort print servers using curren

FastPort User’s Guide E-6c. Use a serial cable with more than three pinsd. Make sure communications parameters are the same, default: 9600, 8, 1, no p

FastPort User’s Guide E-7E.2.7 Downloading the Setup Defaults File to Change FastPortThe Setup Zone Name, Setup Printer Info, and Setup Font List files

FastPort User’s Guide E-815. Double-click on Apple Printer Utility 2.2 or the older LaserWriter Utility 7.6.2 for driver 8 (LaserWriter Utility 7.2 fo

FastPort User’s Guide F-1Appendix FUpgrading Flash EEPROMSDigi offers the latest firmware release for FastPort to be downloaded free from our web- or F

FastPort User’s Guide F-25. MIL-3100CX, MIL-3110FTX, and MIL-3500X FastPorts have an alternate EEPROM bank to boot FastPort if the primary bank fails.

FastPort User’s Guide F-3If the new firmware image does not work, reset FastPort main bank back to older firmware:1. Use: Restart Running Image in Other

FastPort User’s Guide G-1Appendix GTelnet, NBMON and Serial Connection DiagnosticConsole OptionsG.1 Diagnostic and Configuration Commands: Commands• C—

FastPort User’s Guide G-2G.3 D—Display Summary Configuration Parameters, IncludingCommand [?,C,D,E,F,H,I,L,N,P,Q,R,S,Z,*,+] --> dFastPort Model 3200

FastPort User’s Guide G-33.(Display flash chip information)<enter> (don't change/continue)G.6 I—Display/set IP Addresscurrent IP address:

FastPort User’s Guide G-4• PostScript binary disabled• Bi-directional interface disabled• Delay before reset = 15 sec• Delay after reset = 45 secParal

FastPort User’s Guide 1-2 The distribution diskette package includes the following:• Three DOS/Windows diskettes including three utilities: – “FastMa

FastPort User’s Guide G-5• Auto-sense frame type• No primary server configured• Notification disabled• Queue scan rate: 1 sec• Netware Directory Servi

FastPort User’s Guide G-6• Modify?, yes or no (y or n)?:nG.8.1.4.2TCP/IP Menu Options: (L) LPD OptionsLPD options:• LPD enabled• Output Control-D at e

FastPort User’s Guide G-7<enter> (don't change/continue)G.9.1.1 Display/Set for MIL-3110FTX and MIL-3111FTX,Current Parallel port config.:m

FastPort User’s Guide G-8Modify?, yes or no (y or n)?:n1.(300)2.(600)3.(1200)4.(2400)5.(4800)6.(9600)7.(19200)8.(38400)<enter> (don’t change/con

FastPort User’s Guide H-1Appendix HTechnical Support ServicesH.1 WWW and FTP SitesDigi LAN division provides on-line technical support via WWW and our

FastPort User’s Guide H-2If technical support determines that the unit is defective, a return materials authorization (RMA) is issued by our RMA admin

FastPort User’s Guide H-3sun3.tar SUN 3.X on 68K processorsun4_411.tar Sun OS 4.1.1sun4_412.tar Sun OS 4.1.2sun4_413.tar Sun OS 4.1.3sun4_414.tar Sun

FastPort User’s Guide H-4pyr_r3k.tar Pyramid R3000 OSX pyr_rm1k.tar Pyramid RM1000 Mesh MPP/scosco3242.tar SCO Sys 3.2 3.242 sco5.tar SCO open Server

FastPort User’s Guide H-5printers.txt printer compatibility listprotocol.txt protocol support with each firmware revisionserial.txt information for ser

FastPort User’s Guide H-6digilpr.txt Installation instructions for Win95/98 lpr/lpd printingdigidll.txt Digiís DLL support for printing from Windows 9

FastPort User’s Guide 1-3 UNIX, NetWare, or MAC). 6. Turn to the specific chapter in this document for the specific network operating system (refer to

FastPort User’s Guide I-1IndexAAbout Distribution Diskette 1-1About Option Classes 5-10About the Manual P-1Accounting Information 5-15ACK 7-4, C-6Sign

FastPort User’s Guide I-2LLaserWriter utility 6-8, 7-5LEDs D-1LEDs and Switches 1-3Logical Printers 5-2LPDsupport 5-1LPD/LPR Queue Names 5-5LPR Option

FastPort User’s Guide I-3ACT Error Messages C-11Attaching QUEUE1 C-10Autosensing printer C-10FAKEQ C-11FastPort does not power up B-1, C-8MS Windows C

1299 Orleans DriveSunnyvale, CA 94089Part Number: 90000065 Rev. C Printed in the USA

FastPort User’s Guide 2-1 Chapter 2 Setting the IP Address 2.1 Assigning the IP Address Devices on a TCP/IP network are identified by two addresses:•

FastPort User’s Guide 2-2 2.2 Setting an IP Address with Install Script 1. Use “TAR” to get the files from the diskette.2. Run the unpack.sh command

FastPort User’s Guide 2-3 2.4 Setting IP Address with Windows 95, 98, and NT Using ARP or telnet on a Windows systems only works if there is a TCP/IP

FastPort User’s Guide 2-4b. Press [return] and power cycle FastPort.5. Verify that the RARP daemon is running:a. For BSD UNIX, type ps -ax | grep rarp

FastPort User’s Guide 2-57. From the “Boot Protocol” menu, select Actions.8. Select Add. And add the following information:BOOTP Device Name: <spec

FastPort User’s Guide 2-6Figure 2-1: Add Reserved Clients Menu6. Set the DIP switches to the telnet diagnostic monitor position as described in the ha

FastPort User’s Guide 2-72.8 Using Digi's ACT to Assign an IP AddressDigi's ACT can be used to configure options on FastPort.Note:If ACT has

Legal Trademark Rights Digi International™, FastPort™, Print Server Software™, and the Digi logo are trademarks of Digi International, Inc . All oth

FastPort User’s Guide 2-84. Open the Apple Printer Utility.5. Select Download Postscript File from the “Utilities.”6. Select Setup Defaults that were

FastPort User’s Guide 2-9The following output appears:Note:If an error message “0x23 error with add name” appears, this means the NetBEUI stack is not

FastPort User’s Guide 2-108. At the next prompt, type in the IP address as such:Enter new IP address: 204.23.13.49. At the next prompt, press [R] to r

FastPort User’s Guide 3-1Chapter 3Installing and Printing in a MS Windows and IBM OS/2EnvironmentChapter 3 provides detailed instructions on configurin

FastPort User’s Guide 3-24. To configure a system to perform local spooling, refer to:“Spooling Versus Non-Spooling Printing” on page 5Configuration on

FastPort User’s Guide 3-37. Choose a name for the printer.8. Choose the driver for the printer that is connected to the FastPort port. The “Printer Se

FastPort User’s Guide 3-43.1.5 Printing From NetBIOS-supported DOS WorkstationNetBIOS workstations support the DOS-level Net commands for locating and

FastPort User’s Guide 3-53.1.6 Spooling Versus Non-Spooling Printing3.1.6.1 IntroductionNetBIOS machines normally support either spooling or non-spool

FastPort User’s Guide 3-63.2 Printing from a TCP/IP Workstation3.2.1 IntroductionWindows’ systems support a variety of protocols, such as TCP/IP, IPX/

FastPort User’s Guide 3-73.2.2.2 Adding an LPD Printer to Windows NT 3.51. From the “Control Panel,” select the Printers icon.2. From the menu bar, cl

FastPort User’s Guide iii Table of Contents Preface About the Manual...

FastPort User’s Guide 3-85. Click on Add Port-->LPR Port-->New Port.6. In the “Name or address of server providing lpd:” field, enter the FastPor

FastPort User’s Guide 3-95. Choose a directory to install the software package (Default is C:\digilpr. Click Browse to select another directory.Figure

FastPort User’s Guide 3-103.2.5.2 Adding Queues in DigiLprTo create a print queue:1. Double-click on the LPR Utility icon. In the “Queues” pull-down w

FastPort User’s Guide 3-113.2.5.3 Adding a New PrinterTo add a new printer using “Add Printer Wizard”:1. From Start-->Settings-->(open) Printers

FastPort User’s Guide 3-127. Type in a name for the printer and select this printer as the default printer for Windows-based programs. Adding a name i

FastPort User’s Guide 4-1Chapter 4Installing and Printing on NetWareChapter 4 describes how to use ACT (Advanced Configuration Tool) and PCONSOLE for i

FastPort User’s Guide 4-25. Once configuration is done, power cycle FastPort. Wait a few minutes to allow it to login.6. Use PCONSOLE to verify that Fa

FastPort User’s Guide 4-34.2.2 Using PCONSOLE to Install a Print ServerFastPort can be configured for printing without a config. file. This eliminates th

FastPort User’s Guide 4-44.3.1 Installing a Print Server on NDS using PCONSOLE1. Run PCONSOLE using the following command (from the /public directory

FastPort User’s Guide 4-52. Select the printer created and press [Enter].3. Select Print Queues Assigned. Pressing [ins] allows a user to choose from

FastPort User’s Guide iv Printing from Windows NT 4.0 ...

FastPort User’s Guide 4-64.3.2.2 Creating a New Printer1. Under the “Object” pull-down window, click Create. The New Object window appears. 2. Select

FastPort User’s Guide 4-7.Figure 4-2. Print ServerThe printer is now connected to FastPort. Continue to the next section to assign a print queue to th

FastPort User’s Guide 4-84.4 Configuring in a Bindery and NDS EnvironmentFastPort can operate in a mixed Bindery/NDS environment. Use one of the previo

FastPort User’s Guide 4-9Note:If a context was not specified in the NVRAM, it will not logon to NDS.5. FastPort then tries to locate normal Bindery file

FastPort User’s Guide 5-1Chapter 5Installing and Printing on a UNIX Environment5.1 IntroductionTo perform installation on a UNIX TCP/IP client worksta

FastPort User’s Guide 5-25.3 Digi Installation Software1. Log in as root onto the system.2. Create a directory to load the software (e.g., type mkdir

FastPort User’s Guide 5-3– Whether or not the IP information about FastPort has been entered into the host naming method– Ethernet address (on the bot

FastPort User’s Guide 5-45.3.4 Installation on BSD UNIX SystemsInstall.sh creates a spool directory and makes a config. file /usr/spool/<printer name

FastPort User’s Guide 5-5Digi provides an install script to configure UNIX for FastPort. UNIX systems that support LPD include:• BSD UNIX systems• Syst

FastPort User’s Guide 5-6If so, user’s can create a remote printer name called user1. To enable this:1. Telnet into FastPort’s diagnostic port (2002).

FastPort User’s Guide v Printing to FastPort...

FastPort User’s Guide 5-7chown daemon /usr/adm/beta-errschown daemon /usr/adm/beta-acctchmod 644 /usr/adm/beta-errschmod 644 /usr/adm/beta-acct4. Star

FastPort User’s Guide 5-85.4.7 Manual Installation with LPD on RS/60001. Chose a remote system/queue (Rembak: remote spooling).2. Add FastPort to the

FastPort User’s Guide 5-9The fpfilter software supports Adobe TranScript command line arguments. To use these options, rename fpfilter as:• fpcomm: Pr

FastPort User’s Guide 5-10Syntax is shown in Table 5-3. Entries appear and in any order.5.5.2.1 About Option ClassesClass (Table 5-3) supports printin

FastPort User’s Guide 5-115.5.2.2 About Options Startstring and EndstringIf “startstring” and “startfile” are specified, then startstring is sent before

FastPort User’s Guide 5-12Output is then piped to the fpfilter program. To do so:a. First line of the interface file usually is #!/bin/sh. Add a single

FastPort User’s Guide 5-133. Create a script commfilter.sh in the /usr/local/milan.#!/bin/sh/usr/local/milan/fpfilter -P alpha <options> $*exit

FastPort User’s Guide 5-143. Create the spool directory. Change it ownership to daemonmkdir /usr/spool/betachown daemon /usr/spool/betachgrp daemon /u

FastPort User’s Guide 5-15For a parallel printer which will be used by PC-NFS:parallelhostname alpha7. Start the printer and queue by typing the follo

FastPort User’s Guide 5-165.6 Installing and Printing from Data General's DG/UXFastPort supports DG/UX™ 5.4 Release 2.01 and above. Current versi

FastPort User’s Guide vi Appendix C: Troubleshooting NetWare ACT-- Advance Configuration Tool...

FastPort User’s Guide 5-175.6.2 Installing and Printing with DG/UXAfter adding the IP/Ethernet addresses, define a printer. Before doing so, configure F

FastPort User’s Guide 5-189. Supply a printer description, which can include the phone number of the system admin. or location of the printer.Printer

FastPort User’s Guide 6-1Chapter 6Installing and Printing on an Apple NetworkChapter 6 describes installation and configuration of FastPort to print fr

FastPort User’s Guide 6-2FastPort stores all options in NVRAM, including font lists, and LaserWriter 8 values (PostScript version, etc.). Therefore, t

FastPort User’s Guide 6-36.3 Advanced UtilitiesThe advanced utilities portion of the diskette includes:• Readme file• Apple TeachText editor for readin

FastPort User’s Guide 6-46. Edit the list of configuration choices.7. Save the list and quit “TeachText.”8. Open the “Apple Printer Utility” menu.9. Se

FastPort User’s Guide 6-56.4.1.3 Using Setup Font ListFastPort can be told the fonts available for printers connected to the parallel port. If the pri

FastPort User’s Guide 6-66.5 Using Namer to Rename the FastPort PrinterFastPort stores the names of printers connected to its ports. The printer may h

FastPort User’s Guide 6-71. Edit the following two lines to the “Setup Defaults” file. Insert the binary name within the parentheses:Parallel Port Type

FastPort User’s Guide 6-86.7 Bi-directional Printing from Macintosh SystemsFirmware 6.1 supports bi-directional printing to any printer that supports

FastPort User’s Guide vii Configuration to Use the ACK Signal...

FastPort User’s Guide 6-9a. Put switch D1 down and switch D2 up.b. Power cycle FastPort. c. Put the switches back to their original position (D1 up, D

FastPort User’s Guide 7-1Chapter 7Print Management Features of FastPortChapter 7 contains print management and status monitoring for FastPort. This ch

FastPort User’s Guide 7-26. At the command prompt, press [C] from the selection. 7. Press [Y] for yes at the query message Do you want to configure fo

FastPort User’s Guide 7-31. Set the front switches on the FastPort: D1 up and D2 down.2. Run the telnet command. Specifying port 2002 as the connectio

FastPort User’s Guide 7-47. Enter the IP address of the SYSLOG host and the priority of the message(s). Priority level are between 2 and 7. These numb

FastPort User’s Guide 7-5Total parallel bytes sent: 324444554Active serial data session from NetWareSERIAL STATUS: flow control FROM Printer by: XOFFT

FastPort User’s Guide 7-6• It allows users to configure the FastPort settings, like FastManage or any other described utility.• It mimics PCONSOLE for

FastPort User’s Guide A-1Appendix AResetting FastPort to Factory DefaultsA.1 Resetting by Toggling the DIP SwitchesNote:This will also reset the IP Ad

FastPort User’s Guide B-1Appendix BTroubleshooting MS WindowsB.1 MS Windows-Level Browsing and Sharing AbilitiesWhen a client machine comes up on the

FastPort User’s Guide B-21. Use the net use and/or net view command without having FastPort in the same workgroup as the workstation. 2. Fill in the p

FastPort User’s Guide P-1 Preface P.1 About the Manual This manual has the latest firmware and software instructions for all versions of the FastPort

FastPort User’s Guide C-1Appendix CTroubleshooting NetWareC.1 ACT-- Advance Configuration ToolC.1.1 Benefits of ACT• Quick configuration menu• Configurati

FastPort User’s Guide C-2• Resetting FastPort’s NVRAM of to factory defaults• Choosing a primary NetWare server• Enabling/disabling protocols (e.g., T

FastPort User’s Guide C-3• Print Server Configuration: Controls the print server-specific parameters for the selected FastPort.• Fpfilter Configuration

FastPort User’s Guide C-4C.2.1.2Configuring the Print Server (File Server Side)When the Configure Print Server (File Server) is accessed, a set of menu

FastPort User’s Guide C-55. Use an ASCII editor to prepare the following config. file:SIMBA:QUEUEP:PS1:Parallel1::ss=”M-%-12345X@PJL enter language = Po

FastPort User’s Guide C-6• Set and modify access passwords• Enable and disable RARP• Access passwordsNote: Access is password protected. Choose a pass

FastPort User’s Guide C-7C.3 Status Menu in ACTThe Status Menu provides two options to display the current status of a print server and its queues. Th

FastPort User’s Guide C-8C.5 Troubleshooting TipsThis section lists problems and possible solutions for NetWare.C.5.1 FastPort does not power upCheck

FastPort User’s Guide C-9C.5.5 FastPort does not login to the file server• Use the console monitoring capability of ACT (in the Monitor menu) to see th

FastPort User’s Guide C-10C.5.9 Autosensing printer has trouble printing• Check the job time-out value and increase it 45 to 60 seconds.• Turn off ban

FastPort User’s Guide P-2 • “Printing on a UNIX Environment” in Chapter 5• “Installing/Printing on an Apple Network” in Chapter 6• “Print Management

FastPort User’s Guide C-11C.8.3 Could not Read Configuration file from SERVER1FastPort could not find the configuration file or did not have the rights to

FastPort User’s Guide D-1Appendix DTroubleshooting UNIXD.1 IntroductionIf there are problems printing to FastPort while using UNIX:1. Verify that Fast

FastPort User’s Guide D-2• Remove the formfeed option from the “.fpconfig” file. Use install.shOn System V or RS/6000 systems:• Specify an -m argument t

FastPort User’s Guide D-34. For NIS, with the changes made to the /etc/hosts or/etc/ethers file, update the files by typing: cd /var/yp; makeNote:RARP o

FastPort User’s Guide D-4D.4 Sample Entries for Direct and Remote SpoolingThe following are sample printer entries for direct spooling to a parallel P

FastPort User’s Guide E-1Appendix ETroubleshooting AppleTalkE.1 Troubleshooting TipsThe following are troubleshooting tips for AppleTalk.E.1.1 Reset T

FastPort User’s Guide E-23. The PS code that follows is used to switch the LaserWriter into 8 data bit PostScript batch mode with mark parity.Note: Th

FastPort User’s Guide E-3E.2 Setup for AppleTalkPlease confirm or verify on test page:1. DIP switch D1 is up (off).a. The Power LED and the Link LED i

FastPort User’s Guide E-4E.2.2 PostScript Binary printIf the printer driver sends postscript binary print jobs and the printer accepts PS binary, that

FastPort User’s Guide E-5• Before Reset• After Reset DelayThe IP address can be found in the Setup Defaults file.Note:Apple products were only designed