Digi XEB09-BCS Bedienungsanleitung PDF herunterladen



XPress™EthernetBridgeMultipoint:User

Guide

Overview

The XPress Ethernet Bridge (XEB) replaces costly wiring with a solution that can enable industrial

Ethernet PLCs, electronic (LED) signs, remote Wi-Fi APs, Pan/Tilt/Zoom security cameras, VoIP

phones, Internet kiosks and more. With a range of up to 15 miles (line-of-sight with a high gain

antenna) and the ability to transmit through as many as 10 standard walls, the XEB uses the added

range and capabilities of the 900 MHz band to communicate where Wi-Fi and other wireless data

products fall short.

Contents

• 1 XEB RF Modem: XEB09-BCS = Commercial (Indoor), XEB09-BIS = Industrial (Outdoor)

Accessories Kit also includes:

• 1 Half-wave, 2.5 dBi dipole antenna

• 1 6VDC/110VAC power adapter (Commercial only)

• 1 12VDC/110VAC power adapter (Industrial only)

• 1 Power over Ethernet injector (Industrial only)

• 1 XEB Multipoint manual

How It Works

The XEB radios allow you to create a long range, wireless Ethernet network for up to 16 Subscriber

Units (SU) per Access Point (AP). The AP automatically scans for the best of the 12 available radio

channels. Then it encrypts Ethernet data received from the network and transmits it wirelessly to the

correct SU. The AP is constantly

monitoring the network performance and automatically

changes channels if the performance is hindered because

of interference.

Select any of the 12 radio channels by toggling DIP switch settings. (See DIP Settings for additional

information.) It is possible to operate up to 12 APs in the same area with each AP on a different

channel. To avoid interference, space the APs at least 10 feet apart. Typically, the AP is attached to

the wired network via an Ethernet Cable. The Auto MDI/MDIX feature on each XEB will work with

either a straight through or crossover network cable.

Note: The AP does not have a MAC/IP address.

Any 10BaseT Ethernet Client Device (ECD) can be connected to an XEB SU. Each SU encrypts Ethernet

traffic received from the attached ECD and transmits the data wirelessly to its AP. You can plug each

SU directly into an ECD without need for any drivers or loading software on the ECD. Crossover cables

are never needed.

You can only attach one ECD to each SU. The DIP switches on the SU should be in the default OFF

setting. To avoid overloading the radio’s receiver, place the SU at least 10 feet from the AP. 100-foot

spacing is recommended if using high-gain antennas.

Note: The SU does not have its own MAC/IP address.

1 2 3 4 5 6

Inhaltsverzeichnis

Seite 1 - How It Works

XPress™EthernetBridgeMultipoint:UserGuideOverview The XPress Ethernet Bridge (XEB) replaces costly wiring with a solution that can enable indus

Seite 2 - LED Display

2 XEB radios use electronic network keys that allow you to group radios together to form a network. Network keys are shared between radios by connecti

Seite 3 - Initial Setup

3 Name Function Color 12 926.04167 MHz Excellent link quality No retransmissions Green Very good link quality Few retransmissions Green Good link

Seite 4 - Channels and Settings

To Re-key a Subscriber Unit to a New Access Point Use the following procedure to re-key an SU to an AP: 1. Select the radio that will operate as the

Seite 5 - Advanced Operation

5 Advanced Operation Contact Digi Support if your application requires: • Over 16 SUs per AP for roaming/mobility applications • Multiple APs that use

Seite 6 - Contact Digi

Example Illustration Commercial (Indoor) radios can communicate with Industrial (Outdoor) radios. Figure 1: A typical point-multipoint architecture

Kommentare zu diesen Handbüchern

Keine Kommentare

Digi XEB09-BCS Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Nein Digi XEB09-BCS herunter. Digi XEB09-BCS User's Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Digi XEB09-BCS