Digi X2 Bedienungsanleitung

ConnectPort™ X Family User’s GuideConnectPort™ X Family:ConnectPort X2, ConnectPort X4, ConnectPort X890000832_Ae-mail: [email protected]tel: 08-52

Contents10Verify device support of commands...166Configuration th

Configuration through the web interface100Example VPN configurationThe diagram shows a Digi Connect WAN VPN used as a primary remote site router:How V

101Configure Digi devicesIP address requirements for VPN tunnelsTo establish an IPSec VPN tunnel, the IP address of the mobile interface must be publi

Configuration through the web interface102Using a console portThe Digi device’s console port can be configured for Console Management to provide SSH o

103Configure Digi devices1 Assign a static IP address to the Ethernet port.Note that the default address for the Ethernet port is 192.168.1.1. The def

Configuration through the web interface1044 Click VPN Internet Key Exchange (IKE) Settings.

105Configure Digi devices5 In the Identity setting, specify how the VPN client and its security settings will be identified to the remote VPN endpoint

Configuration through the web interface106Aggressive Mode: Processes phase one negotiations with fewer exchanges than Main Mode. In the first exchange

107Configure Digi devices7 Specify the Internet Key Exchange (IKE) Security Settings for the VPN connection. Internet Key Exchange (IKE) negotiates IP

Configuration through the web interface1088 Click VPN Policy Settings to add, modify, or delete a VPN tunnel. VPN Tunnels define the actual tunnels be

109Configure Digi devicesManual-Keyed IPSec/ESP tunnels are established by manually specifying the tunnel and security settings. See page 112 for more

11ContentsManage active system connections... 189Event logging ...

Configuration through the web interface110For example, to configure the ISAKMP VPN tunnel in the example configuration, you would choose ISAKMP and en

111Configure Digi devicesWhen the VPN tunnel has been added to the configuration settings after you click Apply, the VPN Policy Settings page looks li

Configuration through the web interface112Manual-keyed IPSEc/ESP VPN tunnel security settingsManual-keyed IPSec/ESP tunnels specify the tunnel and sec

113Configure Digi devicesThere are two groups of manual-keyed settings, for incoming and outgoing traffic, which differ from each other, depending on

Configuration through the web interface114 Enable AuthenticationAuthentication algorithmAuthentication key: The optional authentication algorithm and

115Configure Digi devicesISAKMP VPN tunnel security settingsISAKMP security settings include a pre-shared key and security policies for incoming and o

Configuration through the web interface116 Use the following pre-shared key to negotiate IKE security settings: The Pre-Shared Key (PSK) specifies th

117Configure Digi devicesVPN tunnel proposal configuration for ISAKMP tunnelsThe Proposal Configuration settings configure a set of security policies

Configuration through the web interface118Advanced network settingsThe Advanced Network Settings are used to further define the network interface, inc

119Configure Digi devicesConfigure mobile (cellular) settingsThe Mobile Settings pages configure how to connect to mobile (cellular) networks using th

Contents12Administration from the web interface... 210File

Configuration through the web interface120Set mobile configuration settings to factory defaultsThe Set to Defaults button on the Mobile Configuration

121Configure Digi devicesProvision a mobile deviceMobile device provisioning is needed to properly configure the Digi device with the required configu

Configuration through the web interface122Automatic versus manual provisioningThere are different types of provisioning methods depending upon your mo

123Configure Digi devices2 Select automatic or manual provisioning.The main difference between automatic and manual provisioning is that manual provis

Configuration through the web interface1244 Device provisioning in progress...5 Provisioning complete.Upon successful completion of provisioning, a sc

125Configure Digi devicesMobile connection settingsMobile connection settings configure how the mobile connection is established and maintained. Re-e

Configuration through the web interface126Hardware reset thresholds Hard reset the modem module after the following number of consecutive failed conn

127Configure Digi devices Ping Test: Enables or disables the use of “ping” (ICMP) as a test to verify the integrity of the mobile connection. The tes

Configuration through the web interface128 DNS Lookup Test: Enables or disables the use of a Domain Name Server (DNS) lookup as a test to verify the

129Configure Digi devices Test only when idle: if no data is received for the above period of time: Specifies that the test repeat interval (above) i

13ContentsGlossary...

Configuration through the web interface130Configure Mesh/ZigBee network settingsA Digi ConnectPort X gateway provides a gateway between an Internet Pr

131Configure Digi devicesrouterA router is a node that creates/maintains network information and uses this information to determine the best route for

Configuration through the web interface132joiningThe process of a node becoming part of a ZigBee PAN. A node becomes part of a network by joining to a

133Configure Digi devicesMesh Network configuration settingsThe Mesh Network Configuration settings (Configure > Mesh Network) displays a view of M

Configuration through the web interface134For example, clicking on the coordinator COORD-ABE displays the Mesh Network Configuration settings for the

135Configure Digi devicesBasic radio settings PAN ID: Sets the PAN (Personal Area Network) ID, in hex. This is the preferred PAN ID for the mesh netw

Configuration through the web interface136Advanced radio settings Transmit Power Level: Sets the power level at which the RF module transmits conduct

137Configure Digi devicesConfigure serial portsUse the Serial Port Configuration page to establish a port profile for the serial port of the Digi devi

Configuration through the web interface138RealPort profileThe RealPort profile maps a COM or TTY port to a serial port. This profile configures a Digi

139Configure Digi devicesTCP Sockets profileThe TCP Sockets profile allows serial devices to communicate over a TCP network. The TCP Server allows oth

Contents14

Configuration through the web interface140TCP and UDP network port numbering conventionsDigi devices use these conventions for TCP and UDP network por

141Configure Digi devicesSerial Bridge profileThe Serial Bridge profile configures one side of a serial bridge. A serial bridge connects two serial de

Configuration through the web interface142Custom ProfileThe Custom port profile displays all serial-port settings, which can be changed as needed. Use

143Configure Digi devicesAdvanced serial settingsThe advanced serial settings allow you to further define the serial interface, including whether port

Configuration through the web interface144TCP settingsThe TCP Settings are displayed only when the current serial port is configured with the TCP Sock

145Configure Digi devices Send data only under any of the following conditions: Enable if it is required to set conditions on whether the Digi device

Configuration through the web interface146UDP settingsThe UDP Settings are displayed only when the current serial port is configured with the UDP Sock

147Configure Digi devicesConfigure camera settingsConnectPort X Family products support connecting a WatchPort Camera to one of its USB host ports. On

Configuration through the web interface148 Current Image: Displays a snapshot of the current camera image. Clicking on the image brings up a new wind

149Configure Digi devicesConfigure alarmsUse the Alarms page to configure device alarms or display current alarms settings. Device alarms are used to

15About this guideAbout this guidePurposeThis guide describes and shows how to provision, configure, monitor, and administer Digi devices.AudienceThis

Configuration through the web interface150Alarm conditionsThe Alarm Conditions part of the Alarms page shows a list of all of the alarms. Up to 32 ala

151Configure Digi devicesAlarm conditionsTo configure an alarm, click on it. The configuration page for individual alarms has two sections: Alarm Con

Configuration through the web interface152Alarm destinationsThe Alarm Destination part of the page defines how alarm notifications are sent—either as

153Configure Digi devicesConfigure system settingsThe System Configuration page configures system settings, including device description information,

Configuration through the web interface154 Destination IP: The IP address of the system to which traps are sent. In order to enable any of the traps,

155Configure Digi devicesConnection settingsThe Connection settings configure how the Digi device connects to the Connectware Manager server. These se

Configuration through the web interface156A server-initiated connection works the opposite way. The Connectware Manager server opens a TCP connection,

157Configure Digi devicesClient initiated management connection settings Enable Remote Management and Configuration using a client initiated connecti

Configuration through the web interface158Advanced remote management settingsThe default settings for remote management usually work for most situatio

159Configure Digi devices– Connection Method: The method for connecting to the Connectware Manager server. TCP: Connect using TCP. This is the default

Where to find more information16Where to find more informationIn addition to this guide, find additional product and feature information in the these

Configuration through the web interface160Alarms and the Connectware Manager serverAll alarms can be sent to the Connectware Manager server for displa

161Configure Digi devicesAbout user models and user permissionsIn Digi devices that have a one-user model: By default, there is no login prompt. The

Configuration through the web interface162Disable password authenticationPassword authentication can be disabled as needed. In the web interface:1 On

163Configure Digi devicesUpload an SSH public keySSH can be configured to log into to servers without having to provide a password. This is called “pu

Configuration through the web interface164Configure applicationsSeveral Digi devices support additional configurable applications. For most devices, t

165Configure Digi devicesPython filesThe Python files page is for uploading Python programs to a Digi device, and managing the uploaded files. Upload

Configuration through the command line166Configuration through the command lineConfiguring a Digi devicethrough the command-line interface consists of

167Configure Digi devicesHere are some examples of commands used to configure Digi devices. See the Introduction of the Digi Connect Family Command Re

Configuration through the command line168Point-to-Point (PPP) outbound connections set pppoutboundport buffering set bufferport profile for a serial p

169Configure Digi devicesConfiguration through Simple Network Management Protocol (SNMP)Configuring Digi devices through Simple Network Management pro

17About this guideAdditional product information on www.digi.comIn addition to the previous documents, product information is available on the Digi we

Configuration through Connectware Manager170Configuration through Connectware ManagerConfiguring Mesh Networks and Nodes through Connectware ManagerCo

171Configure Digi devicesZigBee Networks ViewThe Mesh Networks device management view of Connectware Manager allows for displaying devices within thei

Configuration through Connectware Manager172Node ViewFrom the ZigBee Networks view, more detailed views of devices can be accessed. For example, here

173Configure Digi devices

Batch capabilities for configuring multiple devices174Batch capabilities for configuring multiple devicesFor configuring many Digi devicesat a time, b

175Monitor and manage Digi devicesCHAPTER 3The port, device, system, and network activities of Digi devicescan be monitored for from a variety of inte

Monitoring capabilities in the web interface176 Monitoring capabilities in the web interfaceSeveral device monitoring and connection-management

177Monitor and manage Digi devicesGeneral system informationThe General page displays the following general system information about the Digi device,

Monitoring capabilities in the web interface178 Up TimeThe amount of time the Digi device has been running since it was last powered on or rebo

179Monitor and manage Digi devicesConfigurationThe Configuration section of serial port information includes the electrical interface (Port Type) and

Digi contact information18

Monitoring capabilities in the web interface180 Serial statisticsThe Serial statistics section of serial port information includes data counter

181Monitor and manage Digi devicesNetwork statisticsNetwork statistics are detailed statistics about network and protocol activity that may aid in tro

Monitoring capabilities in the web interface182 IP StatisticsDatagrams ReceivedDatagrams ForwardedNumber of datagrams received or forwarded. Fo

183Monitor and manage Digi devicesEstablished ResetsNumber of established connections that have been reset. UDP statisticsDatagrams ReceivedDatagrams

Monitoring capabilities in the web interface184 Mobile information and statisticsThe Mobile information and statistics page displays detailed m

185Monitor and manage Digi devicesMobile StatisticsMobile statistics include the interface status, bytes received and sent, baud rate, modem resets, a

Monitoring capabilities in the web interface186 Mobile InformationIMSIInternational Mobile Subscriber Identifier (IMSI), a unique 15-digit numb

187Monitor and manage Digi devicesSureLink statisticsDigi SureLink™ provides an “always-on” mobile network connection to ensure that a Digi device is

Monitoring capabilities in the web interface188 total failuresThe total number of times a configured test was attempted but failed since the Di

189Monitor and manage Digi devicesManage connections and servicesThe Management menu is for viewing and managing connections and services for the Digi

19IntroductionIntroductionCHAPTER 1This chapter introduces Digi devices and their product families, types of connections and data paths in which Digi

Monitoring capabilities in the web interface190 Event loggingInformation on this feature to be provided in a forthcoming release.Manage network

191Monitor and manage Digi devicesView and manage current DHCP leasesThe DHCP server maintains a current list of its leases, reservations and unavaila

Monitoring capabilities in the web interface192 Lease status typesDescriptions of Lease Status values that are displayed in the lease list foll

193Monitor and manage Digi devicesReleasedA lease was previously assigned to the given client, but that client has proactively released it. A lease in

Monitoring capabilities in the web interface194 Manage Mesh networks from the web interfaceTo display information about Mesh networks and devic

195Monitor and manage Digi devicesGateway device detailsThis part of the display shows information about the ConnectPort X gateway and its role as a g

Monitoring capabilities in the web interface196 Python Application ZigBee Socket Error CountsThis section includes error counters that are spec

197Monitor and manage Digi devicesMesh device state pagesClicking a device in the Network View of the Mesh Devices displays the Mesh Device State page

Monitoring capabilities from the command line198 Monitoring capabilities from the command lineThere are several commands for monitoring Digi de

199Monitor and manage Digi devicesinfoThe info command displays statistical information about a device over time. The statistics displayed are those g

2  User’s Guide©Digi International Inc. 2007. All Rights Reserved.The Digi logo is a registered trademarks of Digi International, Inc. Digi Con

ConnectPort X Family products20ConnectPort X Family productsThe ConnectPort X Family of products is intended to provide gateway functionality between

Monitoring capabilities from the command line200 set alarmThe set alarm command displays current alarm settings, including the conditions which

201Monitor and manage Digi devicesCommands for managing connections and sessions close: Closes active sessions that were opened by connect, rlogin, a

Monitoring capabilities from the command line202 Commands for managing Mesh networks and nodesSeveral commands are used to configure Mesh netwo

203Monitor and manage Digi devices packet_timeout=0-255 {Packetization timeout, chars} dio0_config=0-5 {AD0/DIO0 configuration} dio1_config=0

Monitoring capabilities from the command line204 display meshThe display mesh command refreshes the display of Mesh network devices, and displa

205Monitor and manage Digi devices#> display mesh address=00:0d:6f:00:00:06:89:31!Status of device: 00:0d:6f:00:00:06:89:31!channel : 18ne

Monitoring capabilities from Connectware Manager206 Monitoring capabilities from Connectware ManagerDigi devices can be monitored and managed f

207Monitor and manage Digi devicesMonitor/manage Mesh networks from Connectware ManagerDigi’s Connectware Manager provides remote network management o

Monitoring Capabilities from SNMP208 Monitoring Capabilities from SNMPDevice monitoring capabilities from SNMP include, among other things: Ne

209Administration tasksAdministration tasksCHAPTER 4This chapter discusses the administration tasks that need to be performed on Digi devices periodic

21IntroductionFeaturesThis is an overview of key features in Digi devices. Software features are covered in more detail in the next three chapters. Ha

Administration from the web interface210Administration from the web interfaceThe Administration section of the web interface main menu provides the fo

211Administration tasksFile managementThe File Management page of the web interface uploads custom files to a Digi device, such as the files for a cus

Administration from the web interface212X.509 Certificate/Key ManagementThe X.509 Certificate/Key Management pages are for loading and managing X.509

213Administration tasksBackup/restore device configurationsOnce a Digi device is configured, backing up the configuration settings is recommended in c

Administration from the web interface214Update firmware and Boot/POST CodeThe firmware and/or boot/POST code for a Digi device can be updated from a f

215Administration tasksRestore a device configuration to factory defaultsRestoring a Digi device to its factory default settings clears all current co

Administration from the web interface216Using the Reset buttonIf the Digi device cannot be accessed from the web interface, the configuration can be r

217Administration tasksDisplay system informationSystem information displays the model, MAC address, firmware version, boot version, and POST version

Administration from the command-line interface218Administration from the command-line interfaceAdministrative tasks for Digi devices can also be perfo

219Specifications and certificationsSpecifications and certificationsCHAPTER 5This chapter provides hardware specifications, additional feature detail

Features22Quick reference for configuring featuresThis guide primarily focuses on configuring, monitoring, and administering Digi devices from the web

Hardware specifications220 Hardware specificationsConnectPort X8 specificationsSpecification ValueEnvironmental Ambient temperature -30 to 60C

221Specifications and certificationsRegulatory information and certificationsSafety standardsThe ConnectPort X8 gateway device complies with the stand

Regulatory information and certifications222 enclosed module FCC ID. This exterior label can use wording such as the following: “Contains Trans

223Specifications and certifications Personal computers and peripheralsThe product listed above has been tested at an External Test Laboratory certif

Important Safety Information224 Important Safety InformationTo avoid contact with electrical current: Never install electrical wiring during a

225••••••••••••••••••••••••••••••••••••••••••••••••••••••••Glossary802.11The IEEE standard for wireless Local Area Networks. It uses three different p

226(DHCP) server. But if the DHCP server is unavailable or nonexistent, Auto-IP will assign the device an IP. If DHCP is enabled or responds later or

227CTSClear to Send.device serverA one- or two-port intelligent network device that converts serial data into network data.DHCPSee Dynamic Host Config

228Encapsulating Security Payload (ESP)A routing protocol used to route (tunnel) various types of information between networks. See also ESP Passthrou

229factory defaultsThe default configuration values that are set in a device at the factory.File Transfer Protocol (FTP)A standard Internet protocol t

23IntroductionAutoconnection: automatically connect a user to a server or network deviceConfiguration > Serial Ports > port > Profile Setting

230HTTPSee HyperText Transfer Protocol.HTTPSSee HyperText Transfer Protocol over Secure Socket Layer. HyperText Transfer Protocol (HTTP)An application

231Internet Group Management Protocol (IGMP)Internet Group Management Protocol (IGMP) provides a way for an Internet computer to report its multicast

232Internet Security Association and Key Management Protocol (ISAKMP)A protocol that defines procedures and packet formats to establish, negotiate, mo

233modem emulationA serial port configuration where the port acts as a modem. The Digi device emulates modem responses to a serial device and seamless

234the BIOS issues an error message which may be text on the display screen and/or a series of coded beeps, depending on the nature of the problem.pro

235– Routers can route data packets to/from other nodes– Can be a data packet source and destination – Are mains-powered RSHSee remote shell.RSSIRelat

236enables a network administrator to manage nodes--servers, workstations, routers, switches, hubs, etc.--on an IP network; manage network performance

237Transmission Control Protocol (TCP)A set of rules used along with the Internet Protocol (IP) to send data in the form of message units between comp

238TXDTransmit eXchange Data.UDPSee User Datagram Protocol.Universal Mobile Telecommunications Service (UMTS)A third-generation (3G) broadband, packet

239sometimes referred to as UDP/IP. Like the Transmission Control Protocol, UDP uses the Internet Protocol to actually get a data unit (called a datag

Features24Ethernet settings Configuration > Network > Advanced Network Settings 118Help on configuring features Help button on each page.Host na

240to 255 devices in a single WPAN.

241Index••••••••••••••••••••••••••••Index1100% CPU utilization 177AAccess Control Lists (ACL) 163access permissions for commands 161Active Opens 182AD

Index242cellular traffic 41, 149certifications 221client-initiated connections 155close command 201Code-Division Multiple Access (CDMA)carrier require

243IndexDHCPSee Dynamic Host Configuration Protocoldhcp command201Diffie-Hellmangroups106protocol description 106Digi Connect WAN VPNconfiguring VPN s

Index244firmware versionupdating214, 218flow control 142, 179Forwarding statistic 182Framing Errors 180Fully Qualified Domain Name (FQDN) 105GGeneral

245IndexLease Status values 192Line Printer Daemon (LPD) 33, 44, 84Link Integrity Monitoring 125link up traps 33, 154Local Configuration port profile

Index246Secure Socket Service 85Secure Web Server (HTTPS) 86Simple Network Management Protocol (SNMP)85Telnet 85Telnet Passthrough 85Transmission Cont

247IndexRealPort 138selecting and configuring 137Serial Bridge 141set profiles command 168TCP Sockets 139, 144UDP Sockets 140, 146POST versiondisplayi

Index248regulatory information 221Remote Login (Rlogin) 33, 84remote managementand IP Pass-through97configuration settings 154See also Connectware Man

249Indexstop bits 142TCP settings 144UDP settings 146serial portsmanaging connections189serial statistics 180server-initiated connections 155session b

25IntroductionMesh network:  Mesh network configuration through web UIConfiguration > Mesh Network 130 Mesh network configuration through Connec

Index250status LED 216stop bits 142SureLinkconfiguration settings125configuring 125description 119statistics 187use 35system connections 189system inf

251IndexIP address requirements 101ISAKMP tunnels 115manual-keyed tunnels 109, 112purpose 99settings 102testing the connection 111tunnel 108Tunnel Pro

Index252

Features26Modem emulation Configuration > Serial Ports > Port Profile Settings > Modem EmulationSee the Connect Family Command Reference for

27Introduction Issue a new/changed password to a userConfiguration > Security 160Serial port configuration: Basic serial port settingsConfigurati

Features28 Use SNMP as primary configuration interfaceBasic network and serial settings configurable through standard and Digi-specific Management In

29IntroductionHardware featuresA summary of hardware features, including power-supply information, is in "Hardware specifications" on page 2

3ContentsContentsContents...

Features30IP protocol supportAll Digi devices include a Robust on-board TCP/IP stack with a built-in web server. Supported protocols include, unless o

31IntroductionSerial data communication over TCP and UDPDigi devices support serial data communication over TCP and UDP. Key features include: Serial

Features32Dynamic Host Configuration Protocol (DHCP)Dynamic Host Configuration Protocol (DHCP) can be used to automatically assign IP addresses, deliv

33IntroductionSupported SNMP trapsSNMP traps can be enabled or disabled. Supported SNMP traps include: Authentication failure Login Cold start Lin

Features34HyperText Transfer Protocol (HTTP)HyperText Transfer Protocol over Secure Socket Layer (HTTPS)Digi devices provide web pages for configurati

35IntroductionGeneric Routing Encapsulation (GRE) PassthroughEncapsulating Security Payload (ESP)ESP PassthroughGeneric Routing Encapsulation (GRE) an

Features36Mobile/Cellular protocolsProtocols supported in the Digi Cellular Family include, unless otherwise noted: Global System for Mobile communic

37IntroductionGeneral Packet Radio Service (GPRS)GPRS is based on Global System for Mobile (GSM) communication. GPRS is a packet-based wireless commun

Features38the network. It will also make it possible to provide new services, such as alternative billing methods (pay-per-bit, pay-per-session, flat

39IntroductionIP address assignment alternativesThere are several ways to assign an IP address to a Digi device: Static IP: Assign a specific IP addr

Contents4HyperText Transfer Protocol (HTTP)HyperText Transfer Protocol over Secure Socket Layer (HTTPS)...34Internet Con

Features40RealPort softwareDigi devices use the patented RealPort COM/TTY port redirection for Microsoft Windows. RealPort software provides a virtual

41IntroductionAlarmsDigi devices can be configured to issue alarms, in the form of email message or SNMP traps, when certain device events occur. Thes

Features42Security featuresSecurity-related features in Digi devices include:  Secure access and authentication: – One password, one permission level

43IntroductionConfiguration managementOnce a Digi device is configured and running, configuration-management tasks need to be periodically performed,

Supported connections and data paths in Digi devices44Supported connections and data paths in Digi devicesDigi devices allow for several kinds of conn

45IntroductionNetwork services associated with serial ports in generalNetwork service connections associated with serial ports in general include: Re

Supported connections and data paths in Digi devices46Network/serial clientsA network/serial client connection is one in which a Digi device initiates

47IntroductionConfiguration capabilities and interfacesFollowing is an overview of the configuration capabilities and interfaces for Digi devices. Cha

Configuration capabilities and interfaces48Configuration interfacesSeveral interfaces are available for configuring Digi devices, including:  The Dig

49IntroductionThe Digi Device Setup wizardThe Digi Device Setup Wizard is a wizard, for configuring Digi devices. It is provided on the CD shipped wit

5ContentsCommand-line interface (CLI)-based client connections... 46Modem emulation (pseudo-modem) client connecti

Configuration capabilities and interfaces50Disadvantages of the Digi Device Setup Wizard as an interface include: While the wizard is available in Mi

51IntroductionDigi Device Discovery utilityThe Digi Device Discovery utility can be used to locate a Digi device and open its web interface. It uses t

Configuration capabilities and interfaces52Advantages of the Digi Device Discovery utility are: It quickly locates Digi devices and basic device info

53IntroductionThe Web interfaceA web interface is provided as an easy way to configure and monitor Digi devices. Configurable features are grouped int

Configuration capabilities and interfaces54Advantages of the web interface include Ease of use, including point-and-click functionality and wizards t

55IntroductionCommand-line interfaceDigi devices can be configured by issuing commands from the command line. The command-line interface allows commun

Configuration capabilities and interfaces56Connectware Manager interfaceConnectware Manager is an optional, centralized device and network management

57IntroductionAdvantages of the Connectware Manager interface are: Allows multiple devices to be managed (configured and monitored) from one source.

Configuration capabilities and interfaces58Simple Network Management Protocol (SNMP)Simple Network Management Protocol (SNMP) is a protocol for managi

59IntroductionStandard MIBs supportedThe standard MIBs supported in Digi Cellular Family devices are: MIB-II (RFC 1213) This is a MIB for managing a

Contents6By entering the Digi device’s IP address in a web browser ...69By using the Digi Device Discovery ut

Monitoring capabilities and interfaces60Monitoring capabilities and interfacesThere are several capabilities and interfaces for monitoring Digi device

61Introduction System Information:– General device information– Serial port information: for each port, the port’s description, current profile, and

Administration tasks62Administration tasksPeriodically, administrative tasks need to be performed on Digi devices, such as: Uploading and managing fi

63Configure Digi devicesCHAPTER 2This chapter describes how to configure a Digi device. It covers these topics:  "Default IP address" on pa

Default IP address64Default IP addressConnectPort X Family products ship with a a default static IP address for the Ethernet port of 192.168.1.1 and a

65Configure Digi devices4 The Digi Device Setup Wizard automatically starts. Select the appropriate platform and click Next.The Digi device discovery

Alternate methods for assigning an IP address66Configure an IP address from the command-line interfaceThe set network command configures an IP address

67Configure Digi devicesTest the IP address configurationOnce the IP address is assigned, test the IP address configuration to be sure it works as con

Configuration through the web interface68 Configuration through the web interfaceConfiguring Digi devices through the web interface involves these tas

69Configure Digi devicesOpen the web interfaceTo open the web interface, either enter the Digi device’s URL in a web browser and log on to the device,

7ContentsUsing pinholes to manage the Digi device ... 96Remote device management and IP pass

Configuration through the web interface70Discover devicesFrom the start menu, select Start > Programs > Digi Connect > Digi Device Discovery.

71Configure Digi devicesOrganization of the web interfaceWhen web interface is opened, the Home page is displayed. Here is a home page for a ConnectPo

Configuration through the web interface72The Home pageThe left side of the Home page has a menu of choices that display pages for configuration, manag

73Configure Digi devicesApplication pagesDepending on the Digi device, there may be an Application menu item for configuring various applications avai

Configuration through the web interface74Change the IP address from the web interface, as neededNormally, IP addresses are assigned to Digi devices ei

75Configure Digi devicesConfigure network communicationsThe Network configuration pages include: IP Settings: For viewing IP address settings and cha

Configuration through the web interface76Alternatives for configuring network communicationsThere are three ways a Digi devicecan be configured on the

77Configure Digi devicesDHCP server settingsThe DHCP server feature can be enabled in a Digi device to allow other devices or hosts on this network to

Configuration through the web interface78leaseA lease is the length of time that the DHCP server specifies, during which a client host can use an assi

79Configure Digi devicesAddresses in the DHCP server settingsThe IP address and subnet mask of the DHCP server's scope are the static IP configur

Contents8Configure Mesh/ZigBee network settings ...130Mesh network terms .

Configuration through the web interface80 Check that an IP address is not in use before offering it: When a DHCP client requests a new IP address lea

81Configure Digi devices Address Exclusions: A specific set of IP addresses to exclude from the scope. The DHCP server will not grant leases to clien

Configuration through the web interface82Network services settingsThe Network Services page shows a set of common network services that are available

83Configure Digi devicesSupported network services and their default network port numbersIn Digi devices that have multiple serial ports, the network

Configuration through the web interface84The following table shows the network services, the services provided, and the default network port number fo

85Configure Digi devicesSecure Shell (SSH) Allows users secure access to log in to the Digi device and access the command-line interface.22Secure Shel

Configuration through the web interface86Network services and IP pass-throughThe IP pass-through feature (Configuration > Network > IP Pass-thro

87Configure Digi devicesDynamic DNS update settingsA Dynamic DNS (DDNS) service allows a user whose IP address is dynamically assigned to be located b

Configuration through the web interface88 DynDNS.org DDNS Service: You must create your account at DynDNS.org before you can successfully register th

89Configure Digi devices– Standard HTTP port 80 – Alternate HTTP port 8245 – Secure HTTPS port 443 Status and history informationFollowing the setting

9ContentsAlarm destinations... 152Enable and Disable Alar

Configuration through the web interface90IP filtering settingsYou can better restrict your device on the network by only allowing certain devices or n

91Configure Digi devicesIP forwarding settingsWhen a Digi device acts as a router and communicates on both a private and public network with different

Configuration through the web interface92 Forward protocol connections from external networks to the following internal devices: Enables protocol for

93Configure Digi devicesSocket tunnel settingsA Socket Tunnel can be used to connect two network devices: one on the Digi device’s local network and t

Configuration through the web interface94IP pass-through settingsThere are many application scenarios where a router is used to decide upon alternativ

95Configure Digi devicesIf the third-party router’s WAN interface is attached to the Digi device’s Ethernet port, and the Digi device’s mobile interfa

Configuration through the web interface96How IP pass-through affects network access to Digi devicesWhen IP pass-through is enabled, the Digi device ef

97Configure Digi devicesConnectware Manager and Digi SureLink ports are automatically set up as pinholes so that they continue to work with the Digi d

Configuration through the web interface98The screen shot shows IP Pass-through configuration settings.

99Configure Digi devicesVirtual Private Network (VPN) settingsVirtual Private Networks (VPNs) are used to securely connect two private networks togeth